UV Water Purification |
![]() |
Call 1-877-811-REST to Order
|
..Bio-Logic™ ultraviolet water purifier with the Pure Water Pack System |
||
![]() |
•
1.5
gallons per minute, 90 GPH |
|
| ..Minipure™ ultraviolet water purifiers |
||
![]() |
•
1
to 9 gallons per minute, 60 to 540 GPH (gallons per hour) |
|
| ..Mighty Pure™ ultraviolet water purifiers |
||
![]() |
•
2
to 20 gallons per minute, 120 to 1200 GPH (gallons per hour) |
|
| ..Sanitron™ ultraviolet water purifiers |
||
![]() |
NEW!
Model S2400C with removable & rotateable heads |
|
| ..Megatron™ ultraviolet water disinfection system |
||
![]() |
•
90
to 450 gallons per minute, 120,000 to millions of gallons per day |
|
| ..Magnum™ ultraviolet open channel water disinfection system |
||
![]() |
•
35
to 695 gallons per minute, up to 2 million gallons per day |
|
ACCESSORIES
| ..Guardian™ ultraviolet monitor |
||
![]() |
The Guardian™ ultraviolet monitors - monitor the intensity of germicidal ultraviolet energy, which penetrates the quartz sleeve and water within the disinfection chamber, while indicator lights and intensity meter provide visual indication of the ultraviolet intensity. Available in 120v 50/60Hz and 220-240v 50/60Hz, 12vDC, and 24vDC available. Available for use with: Sanitron™ - all models and Mighty Pure™ - all models |
|
| ..Sentry™ safety sensor |
||
![]() |
The Sentry™ safety sensors provide constant visual monitoring of the water purifier's ballast and germicidal lamp operation; indicator lights provide visual indication of ballast and germicidal lamp status. Available in 120v 50/60 Hz and 220 - 240v 50/60Hz. Available for use with: Sanitron™ - models up to 20 GPM, Mighty Pure™ - all models and Minipure™ - all models |
|
| ..SterAlert™ lamp status alarm |
||
![]() |
The SterAlert™ lamp status alarm monitors visible light emitted through the sight port plug of the water purifier and activates an audible alarm when visible light falls below acceptable levels. Operates on a 9v battery or optional 120v 60Hz Power Adapter available. Available for use with: Sanitron™ - all models and Mighty Pure™ - all models |
|
| ..Sentinel™ remote indicator |
||
![]() |
Sentinel™
Remote Indicator monitors lamp operation of one, two, or four lamp ultraviolet
units and comes standard with 25-foot connector cord. Additional 25-foot
extensions are available. The Sentinel™
Remote Indicator can be configured for use with a wide variety of germicidal
ultraviolet fixtures. The Sentinel™
Remote Indicator mounts on a surface close to your ultraviolet unit. Its
wires and sensors are connected to the unit through holes in the unit
wall. Wires from the unit's lamps are wound through the Sentinel's™
Sensors. These sensors detect the flow of current from the lamps, activating
the indicators on the face of the Sentinel™
. When a sensor does not detect a current, its corresponding indicator
will not light. For use with with some of the Air Disinfection line of
equipment. |
|
| ..Élan™ stainless filter |
||
![]() |
Élan™ Stainless Filters out performs conventional filters because the outlets are located above the inlets, providing numerous advantages. Available in a diverse range of flows and variety of micron ratingss. |
|
| ..SureFlo™ flow control valves |
||
![]() |
A complete line of 3 gpm to 40 gpm, Type 304 Stainless Steel valves are available. SureFlo™ Flow Control Valve limits water flow to the rated capacity through the ultraviolet water purifier. For example, if your water purifier has a maximum rated flow of 12 gallons per minute, a 12 gpm flow control valve installed in the water line before the purifier will automatically prevent the water flow from exceeding that rate. Use of the Flow Control Valve is recommended by the U.S. Public Health Service "Criteria for the Acceptability of an Ultraviolet Disinfection Unit". For use with all Sanitron™ and Mighty Pure™ and Minipure™ Ultraviolet Water Purifiers.. |
|
Call 1-877-811-REST to Order